Sink Attachments

Showing all 10 results

  • Standard Model

    The STANDARD non-skid profile is the first one that was commercialized. After several years and thousand of meters sold, this profile represents the best compromise between grip, aesthetic and cost. It is the most recommended non-skid profile for outsides because of its higher height and consequently its better efficacy when snowing or freezing.
    Test DIN 51130 polished granite tile with a 10 cm class R11 (As reported by CTE-Spain Technical Building Code)
    Test Wet Dynamic Coefficient of Friction (DCOF) in order Standard ANSI A137.1-2012, Section 9.6.1 BOT-3000E (according USA)

    Select options
  • 5MM Model

    The 5MM non-skid profile differs from the Standard one by its minor penetration and external height. The thickness of the drop-in part is less, so it can be installed by using any kind of diamond blade (even if it is worn out). It is perfect for slender marbles and ceramics.
    Test DIN 51130 polished granite tile with a 6 cm class R11 (As reported by CTE-Spain Technical Building Code)
    Test Wet Dynamic Coefficient of Friction (DCOF) in order Standard ANSI A137.1-2012, Section 9.6.1 BOT-3000E (according USA)

    Select options
  • Plus Model

    The anti-slip «PLUS» profile maintains some of the characteristics of «5MM» as the least depth of embedding, the rounded lower edges and grooves made in the walls to improve the bonding and increases the active surface to 16.8 mm with a protruding content in just 2 millimeters.
    Test DIN 51130 polished granite tile with a 8 cm class R11 (As reported by CTE-Spain Technical Building Code)
    Test Wet Dynamic Coefficient of Friction (DCOF) in order Standard ANSI A137.1-2012, Section 9.6.1 BOT-3000E (according USA)

    Select options
  • Plus-X Model

    Applying the model Plus an exclusive machining StopSkid, the result is this variant, which we call «PLUS-X». This non-slip profile further enhances the excellent grip of our profiles, but above all, significantly improves longitudinal grip, although in most cases inconsequential, in specific cases can be decisive.
    Test DIN 51130 polished granite tile with a 8 cm class R11 (As reported by CTE-Spain Technical Building Code)
    Test Wet Dynamic Coefficient of Friction (DCOF) in order Standard ANSI A137.1-2012, Section 9.6.1 BOT-3000E (according USA)

    Select options
  • 2cm Model

    The 2CM non-skid profile requires a groove of 18/20 mm. width and 4 mm. depth. These grooves are common among marble workers that usually utilize carborundun. Since the carborondum process is laborious and bothersome, this profile reduces the time performed noticeably, enhances the aesthetic. It is long lasting and easily replaceable (if required).
    It should be pointed out that once it is installed it protrudes 0,8 mm. only.Test Wet Dynamic Coefficient of Friction (DCOF) in order Standard ANSI A137.1-2012, Section 9.6.1 BOT-3000E (according USA).

    Select options
  • PE-B Model

    The countertop protector PE-B model, STOPSKID® exclusive, is integrally made of stainless steel with the exception of a small Teflon feet that serve as support on the surface of the countertop to
    avoid possible scratches. The great advantage of this model is its versatility and ease of use.
    Integrated into the backsplash or directly overlaid on the back wall of the counter, always be on hand providing us with an effective surfaces for hot pans but attention only when it is required, thus sparing the problem, what to do with the when not needed. The solution adopted is simple while effective. If we do not need, we’ll leave it in its upright position without trouble, and when required, with a simple gesture, we’ll have it ready. It is also removable so it can move to where we more comfortable, even the dining table if you wanted, and when no longer do we need, another simple gesture will pick you up at its location, ready for the next use .

  • PE-P Model

    The PE-P countertop protector is composed of 5 stainless steel 250×13.5×3 mm satin finish rods developed by StopSkid. To install make 5 slots with a standard cutting disc of 240/245 mm by 10/15 mm deep. The plates are shaped to fit into these grooves and protrude from the face of the countertop 3.5 mm. The PE-P does not need to be attached and can be easily removed for cleaning.

  • PE-V Model

    The StopSkid exclusive PE-V countertop protector has 5 polished stainless steel rods of 250 x 5mm, with two 4 x 3 mm pins. It is easily installed by making two holes that are 4 mm deep and 3mm in diameter. Like the PE-P model, it does not need to be attached to the counter.

  • Low level sinks hooks

    The low-level sink hooks is very useful and convenient attaching kit for low-level sinks.

    This includes: a brass anchor, a socket set screw, a nut, a 20 mm. washer and a 12 mm. washer.

    Brass anchor options:
    a) 16 mm. long, 5 mm. diameter
    b) 11 mm. long, 5 mm. diameter (it is perfect for 2 cm. thickness marble)

    The kit’s components are stainless: the anchor is made of brass and the rest of the parts are made of stainless steel. Two washers are included (different diameters) in order to choose the best one according to the sink.

    Select options
  • TT – Curtailment ends for blind grooves

    If visual appeal or design of the step prevents you from cutting a groove the full length of the step, StopSkid® offers the possibility of making a recess at the end. This allows the profile to fit into the curved bottom center of the slot so it covers the step entirely, reference “TT”. When the profile is seated,
    the slot not will be exposed. The end (see arrow) has a 1 cm. flat area to allow an acceptable margin when slotting the marble, so you do not have to make the slot fit precisely. These flat ends are available for all models except the 2CM model.

STOPSKID puede ayudarte

Contacta con nosotros